A 40:1 inositol premix contains 40 parts myo-inositol to 1 part D-chiro-inositol by weight, which means the finished blend is 2.44% DCI. That single number explains why brands buy the premix instead of blending the two isomers in-house: at a 2.44% inclusion, one weighing mistake, one segregation pocket or one unverified lot changes the dose printed on the label without changing the appearance of the powder. This guide covers the arithmetic, the two failure modes that matter, the specification lines to write down, and what a Certificate of Analysis should prove before you release a batch.
What 40:1 Means in Grams
The ratio is by weight, not by molecule count, and it describes the two actives only – not the total weight of a capsule or a sachet. Once you fix the myo-inositol dose you want per serving, the premix weight and the DCI dose follow directly.
| Myo-inositol per serving | Premix needed (40:1) | D-chiro-inositol delivered | DCI share of the blend |
|---|---|---|---|
| 1,000 mg | 1,025 mg | 25 mg | 2.44% |
| 2,000 mg | 2,050 mg | 50 mg | 2.44% |
| 4,000 mg | 4,100 mg | 100 mg | 2.44% |
Two practical consequences follow. First, the premix is almost entirely myo-inositol by mass, so most of the capsule or sachet weight is the cheap half of the pair. Second, the label should state both isomers separately – “2,000 mg myo-inositol and 50 mg D-chiro-inositol” is verifiable; “2,050 mg inositol blend” is not, because a buyer cannot check the ratio from it.
Why Brands Buy a Premix Instead of Blending In-House
- Weighing accuracy at 2.44%. Dispensing 50 mg of DCI into a 2 g serving is a small weighment with a large error budget. A pre-blended lot moves that error to the supplier’s blending step, where it is measured and reported.
- Dust and static. Both isomers are fine, freely soluble powders that behave badly in open blending rooms. A sealed premix reduces handling exposure and product loss.
- One traceability chain. Instead of two incoming lots, two COAs and two expiry dates per batch, the brand carries one premix lot with a single ratio and a single assay.
- Fewer process steps to validate. In-house blending requires a homogeneity study on your own equipment. Buying the premix moves that validation upstream, which matters most for contract manufacturers running many SKUs.
The Two Failure Modes: Segregation and Ratio Drift
Blending two powders that are 40:1 apart is a segregation problem before it is a chemistry problem. Myo-inositol and DCI differ in particle size, bulk density and surface behaviour, so vibration during filling, transport or tableting can move the fine fraction away from the coarse one. The result is a blend whose average assay looks correct while individual capsules sit at 30:1 or 50:1.
Ratio drift is the second failure: the blend is homogeneous but was made at the wrong ratio, usually because the DCI weight was rounded, the assay of the incoming DCI lot was not corrected for purity, or a carrier was added after the ratio was set. A 98% DCI lot used as if it were 100% shifts a nominal 40:1 blend to roughly 40.8:1 – small, but it compounds with every other rounding decision.
Both failures are detectable before release:
- Sample top, middle and bottom of the blender or the drum, not a single scoop.
- Assay both isomers separately by HPLC and calculate the ratio from the results, rather than trusting the batch record.
- Report a uniformity figure (relative standard deviation across sampling points) and set an acceptance limit in the specification.
- Repeat the check after filling, on a finished sachet or capsule, if the product is a high-value SKU.
Writing the Specification
Most premix quotations fail at the specification stage because the buyer writes “40:1 inositol premix” and nothing else. The lines below are what a defensible specification contains.
| Parameter | What to write | Why it matters |
|---|---|---|
| Myo-inositol assay | 95.0-99.0% by HPLC (or the grade you buy) | Sets the mass balance for the ratio calculation |
| D-chiro-inositol assay | 98.0% minimum by HPLC | The expensive half; purity drives dose accuracy |
| Ratio | 40:1, with a tolerance such as 38:1-42:1 | A ratio with no tolerance cannot be enforced |
| Homogeneity | RSD limit across top/middle/bottom samples | Catches segregation before it reaches filling |
| Appearance and particle size | White powder or DC granules; mesh range | Controls flow, compression and dissolution |
| Moisture | Typically 1.0% maximum | Both isomers are hygroscopic; free water drives caking |
| Contaminants | Heavy metals, microbiology, ethylene oxide, PAH, pyrrolizidine alkaloids | Routine EU buyer requirements for this category |
| Carrier | “None” or the carrier name and inclusion rate | An undeclared carrier silently dilutes the ratio |
What the COA Should Prove
A premix COA that reports a single “inositol” figure is not usable for release. Ask for separate HPLC results for myo-inositol and D-chiro-inositol, the calculated ratio, the homogeneity result, moisture, and the contaminant panel. The ratio should be calculated from the measured assays of that lot, not copied from the master formula – the two diverge whenever an incoming lot is not exactly at its nominal purity.
Core Nutrix supplies both halves of the blend directly: myo-inositol at 95-99% by HPLC from a corn-derived route, and D-chiro-inositol at 98% by HPLC. Because both are made in the same supply chain, the premix ratio is fixed at the blending step and reported per lot.
Formats, Carriers and Packaging
Three formats cover most launches. Bulk powder in 25 kg drums suits capsule fillers and pouched powders. DC granules flow and compress directly, which removes a granulation step for tablet lines. Sachet-ready blends are the fastest-growing format in women’s health because a 2 g stick pack is easier to take than four capsules.
If a carrier is used, it must be declared and the ratio must be defined on the actives, not on the total weight. A maltodextrin carrier at 10% of the blend does not change the 40:1 relationship between the two isomers, but it does change the grams of premix a customer must weigh – and it must appear on the ingredient list.
What Drives the Cost
At the indicative FOB ranges published on our product pages, myo-inositol is a single-digit-to-low-double-digit cost per kilogram while DCI is in the hundreds. Even at 2.44% of the blend weight, DCI accounts for roughly half of the material cost of a 40:1 premix. That has two implications for buyers: the ratio is where the money is, and a quotation that is dramatically cheaper than the market is usually cheaper on the DCI assay, the ratio or the documentation – not on the myo-inositol.
Request a Premix Sample Read the 40:1 Ratio Guide Contact Us
Frequently Asked Questions (FAQ)
Does 40:1 mean 40 mg of myo-inositol to 1 mg of D-chiro-inositol?
Yes – it is a weight ratio, so 40 g of myo-inositol to 1 g of DCI, or 2,000 mg to 50 mg. The ratio applies to the two actives, not to the total weight of a capsule or sachet.
Can you supply 20:1 or a custom ratio?
Yes. Premixes can be blended to the ratio in your specification, including 20:1, 3.6:1 and custom targets, provided the ratio and its tolerance are stated in writing. Custom ratios are quoted against the DCI assay of the lot used.
Is the premix carrier-free?
The standard 40:1 premix is carrier-free – it contains only the two isomers. If your process needs a carrier for flow or dosing, we can quote a carrier-based version, but the carrier and its inclusion rate are declared on the COA and the specification.
How do you verify homogeneity?
By sampling top, middle and bottom of the blend, assaying both isomers separately by HPLC and reporting the relative standard deviation. The acceptance limit is agreed in the specification before the batch is made.
Can you supply sachets or stick packs?
We supply the premix in bulk; stick-pack filling can be arranged with your contract manufacturer or through our OEM service. Tell us the fill weight and the target ratio and we will confirm the grade.
What is the MOQ and lead time for a premix?
Samples start at 0.5-1 kg with freight collect. Bulk premix typically starts from 10-25 kg depending on the DCI content, with 15-60 days standard lead time and 7-15 days for in-stock small batches.
