Mushroom Extract Specification Guide

Two mushroom extracts can both be sold as “30% polysaccharides” and behave nothing alike in a capsule. The difference is not the number on the label – it is which part of the organism was extracted, which analytical method produced the number, and what the certificate of analysis leaves out. Four questions separate a defensible mushroom specification from a marketing one: which part, which marker, which method, which contaminants. This guide works through each, using reishi and CS-4 as the reference cases.

Question 1: Fruiting Body or Mycelium-on-Grain?

Material What it contains What the label should say
Log-cultivated fruiting body The full polysaccharide and triterpene profile of the mushroom itself “Fruiting body extract” – and the extract ratio or assay
Mycelium on grain Mycelium plus a large share of the grain substrate it grew on – largely starch “Myceliated grain” or “mycelium biomass”, not “mushroom extract”
Submerged fermentation (CS-4) Mycelium grown in liquid, no grain carrier “Fermented mycelium” with the species and strain named

The commercial incentive to blur this is obvious: grain-grown material is far cheaper per kilogram. The tell is in the specification. If the COA reports only total polysaccharides and the pack says “mushroom extract” with no part named, ask for the part in writing. A supplier who will not put “fruiting body” or “myceliated grain” on the specification has usually answered the question already.

Question 2: Which Marker?

Each species has a different set of meaningful markers, and a specification built on the wrong one cannot be verified.

Species Markers used in trade Note
Reishi (Ganoderma lucidum) Polysaccharides (UV) plus triterpenes (HPLC, e.g. ganoderic acid A) Dual standardisation is the defensible option; polysaccharide-only grades may carry little triterpene
CS-4 (Samsoniella hepiali) Mannitol, adenosine, polysaccharides Cordycepin is a Cordyceps militaris marker, not a CS-4 marker
Lion’s mane (Hericium erinaceus) Beta-glucan; fruiting body identity Hericenones and erinacines are research markers, rarely routine on a commercial COA
Chaga (Inonotus obliquus) Beta-glucan, betulinic acid Betulinic acid also indicates how much birch substrate is in the material

Question 3: Which Method?

“Polysaccharides 30% (UV)” is the most common line in this category, and it is the least comparable. A UV colorimetric method measures everything that reacts with the reagent – including starch from a grain substrate and residual glycerol from a liquid culture – so a heavily diluted myceliated grain can post a respectable polysaccharide number with very little fungal beta-glucan in it.

  • UV polysaccharides is a useful, cheap screen, but it is not a purity measure. Always pair it with the part of the organism used.
  • Beta-glucan by enzymatic kit (Megazyme-type) is more specific to the fungal cell wall and is the number to ask for when the claim is immune-related positioning.
  • HPLC triterpenes is what separates a real reishi extract from a brown powder; ganoderic acid A is the usual reference compound.
  • Marker assays for CS-4 (mannitol, adenosine) should state the method, because mannitol results differ substantially between titration and HPLC.

Whatever the method, the specification should name it. “Polysaccharides 30%” without a method is not a specification – it is a number that two labs can reproduce differently.

Question 4: Which Contaminants?

Fungi are efficient accumulators, which makes the contaminant panel more important here than in most botanical categories.

  • Heavy metals by ICP-MS – lead, arsenic, cadmium, mercury. Cadmium is the usual failure point for mushroom materials.
  • Microbiology – total plate count, moulds and yeasts, coliforms, Salmonella, Staphylococcus aureus.
  • Pesticide residues against EU MRLs (EC) 396/2005, and an irradiation statement.
  • PAH and pyrrolizidine alkaloids where the drying or the botanical mix makes them relevant.
  • Species identity – ITS sequencing or a strain-specific method, especially for CS-4 and for anything sold as “cordyceps”.

How to Read a Mushroom COA in Five Minutes

  1. Does it name the part (fruiting body / mycelium / fermented mycelium) and the species?
  2. Does the marker line state the method, and is the marker the right one for that species?
  3. Is there a beta-glucan figure, or only total polysaccharides?
  4. Are cadmium and lead reported with actual results rather than “conforms”?
  5. Is there an identity test, and does the batch number match the drum?

If three or more answers are missing, the material may still be fine – but you cannot prove it, and in the EU the burden of proof sits with the brand placing the product on the market.

EU Documentation and Claims

Mushroom ingredients have no authorised EFSA health claims. The workable EU route is to keep the mushroom for the story and put the claim on an ingredient that has one – vitamin C, vitamin D or zinc in immune positioning – while the label describes the mushroom factually. For CS-4 specifically, the Novel Food position is species-dependent, and it is covered in the CS-4 guide.

Core Nutrix supplies reishi extract standardised to 30% polysaccharides (UV) and 6% triterpenes (HPLC) from log-cultivated fruiting bodies, with a USDA/EU organic option, and quotes CS-4 against customer specification. Batch COAs carry the full contaminant panel described above.

← Back to all guides

View Reishi Extract  CS-4 EU Status  Request Free Samples

Frequently Asked Questions (FAQ)

Is fruiting body extract better than mycelium?

They are different materials, not grades of the same thing. Fruiting body extract carries the mushroom’s own polysaccharide and triterpene profile; mycelium-on-grain includes the grain substrate unless it is separated. For a premium claim, fruiting body is easier to defend.

Why does my supplier’s polysaccharide number look higher than a competitor’s?

Usually because of the method, the part used, or both. UV polysaccharides include starch and glycerol, so grain-grown or liquid-culture material can score high. Ask for beta-glucan as well before comparing.

What beta-glucan level should I specify?

There is no single legal minimum. Set the level from your own finished-product claim and the material you can actually buy consistently; a specification you cannot repeat across lots is worse than a modest one you can.

Is reishi a Novel Food in the EU?

Reishi has a long history of food use in parts of the EU, but the position is not uniform across member states and depends on the part and the preparation. Confirm the current status for your destination market before launch – we provide a written position with the batch documents.

How do I verify species identity?

ITS sequencing is the standard method; strain-specific PCR is used where a particular strain is claimed, as with CS-4. Ask for the report, not just a statement on the COA.

What is the MOQ and lead time for reishi extract?

Samples start at 1 kg with freight collect and bulk orders from 25 kg, packed in 25 kg drums. Standard lead time is 15-60 days; in-stock small batches can ship in 7-15 days.

Leave a Comment or Ask a Question

No account or email needed - just enter a display name. We answer questions within 24 hours.

Scroll to Top